Bottle calculator: how many bottles a batch will fill
Enter your batch size and bottle size, and see how many bottles you’ll fill and how many to sanitise, with a few spare, so you’re never hunting for a clean bottle with the bottling wand dripping in your hand.
The calculator
What’s in the fermenter.
The sediment, and what the tubing and bottling bucket keep: about a litre, more for a dry hopped or fruited brew. Remembered for next time.
Extra bottles to sanitise in case one is chipped, a cap won’t seal or the batch comes out bigger. Remembered for next time.
How it works
Not all of the batch makes it into bottles. The yeast sediment at the bottom of the fermenter stays behind, along with a little in the tubing and the bottling bucket, so the calculator takes that off first. About a litre is typical for a 20 to 23 litre batch; a dry hopped beer or one with fruit in it leaves more.
What’s left, divided by the size of a bottle, is how many it fills. If the last bottle would only be part full, it’s counted as one more, so you have somewhere to put it.
Spares are a share of the bottles you’ll fill, rounded up: 10% gives seven spares for 63 bottles. Sanitise them with the rest. A bottle with a chip in its neck, a cap that won’t crimp or a swing-top seal that’s perished is far easier to swap for a clean one than to sort out mid-flow, and it’s better to tip a few unused ones out afterwards than to run short. Have as many caps or corks ready as bottles.
A bottle size can be given in millilitres, centilitres, litres, fluid ounces or pints: choose “Another size” and its unit. UK and US fluid ounces and pints aren’t the same, so pick the right one: a UK pint is 568ml, a US pint 473ml.
From our brews
I Am Your Guava was 21 litres in the fermenter and filled sixty-two 330ml bottles: 20.5 litres, so about half a litre stayed behind. Entered with half a litre left behind, the calculator says 62 full bottles and a 63rd with a little in it; with 10% spare, that’s 70 to sanitise.
Pilot Episode filled 42 bottles of 500ml, and Sauvignon Plonk six 750ml wine bottles from a 4.5 litre batch.
Questions
- How many bottles do I need for a 23 litre kit?
- Allowing a litre for the sediment, about 67 bottles of 330ml, 44 of 500ml or 30 of 750ml, plus a few spare. A “40 pint” kit makes about 23 litres, so it’s the same.
- How much beer is lost to sediment?
- Usually half a litre to a litre and a half in a 20 to 23 litre batch: the yeast cake, plus what the tubing and bottling bucket hold back. Dry hopping or fruit in the fermenter can double it. Note how many bottles each batch actually fills, and you’ll soon know your own figure.
- How many spare bottles should I sanitise?
- About 10%: half a dozen or so for a full-size batch. Enough to swap out a chipped bottle or a cap that won’t seal, and to catch the last of the beer if the batch comes out a little bigger than you expected.
- What do I do with the last, part-filled bottle?
- Use a smaller bottle if you have one, especially if you prime each bottle with carbonation drops: a half-full bottle gets as much sugar as a full one, so it ends up much fizzier. If you prime the whole batch, a part-filled bottle is fine; just drink it first.
- Can I mix bottle sizes?
- Yes. Decide how many of the bigger bottles you want to fill, take off what they hold (12 bottles of 500ml is 6 litres) and put what’s left into the calculator with the smaller size. The carbonation calculator gives each size its own amount of sugar or drops.
More tools
ABV calculator
Work out a homebrew’s ABV, attenuation and calories from hydrometer readings, including fruit or sugar added during fermentation.
Open the ABV calculatorHydrometer correction
Correct a hydrometer reading taken from warm or cold wort or beer to its true gravity, for the temperature your hydrometer is calibrated to.
Open the hydrometer correctionCarbonation calculator
How much priming sugar, or how many carbonation drops, to put in each bottle for the fizz you want: for 330ml, 500ml and 750ml bottles.
Open the carbonation calculatorWater calculator
Mash and sparge water for an all-grain brew day, from your grain bill, batch size and kettle’s boil-off, with a warning before the kettle overflows.
Open the water calculatorIBU calculator
Estimate how bitter a homebrew will be, in IBU, from the hops you boil, the alpha acid on each packet and how long each one boils.
Open the IBU calculatorRecipe scaler
Scale a homebrew recipe or kit to the batch size you want: grain, hops, sugar and fruit, from a big kit down to a demijohn or up to a bigger brew.
Open the recipe scalerDilution calculator
How much water to add to bring your wort or beer down to a gravity, or what the gravity will be once you top it up with water.
Open the dilution calculator